Features of heat pipe cooling battery technology

A review on the performance of oscillating heat pipe used in battery …

A review on the performance of oscillating heat pipe used in battery cooling. R. Suresh Kumar, R. Suresh Kumar ... N. Jayanthi. Department of Physics, R.M.K. College of Engineering and Technology, Puduvoyal, India. Search for more papers by this author. ... For Lithium-ion (Li-ion) battery packs used in Electric Drive Vehicles (EDVs), …

Modeling and optimization of micro heat pipe cooling battery …

Dynamic thermal behavior of micro heat pipe array-air cooling battery thermal management system based on thermal network model. Appl. Therm. Eng., 162 (2019), ... Optimization of air-cooling technology for LiFePO4 battery pack based on deep learning. J. Power Sources, 497 (2021), Article 229894. View PDF View article View in …

Review of battery thermal management systems in electric vehicles

The heat produced by the li-ion cell occurs through both Joule heating effects and reversible heat generation effects at the solid and electrolyte phases when charge is transported [6].The rate of charging and discharging of the li-ion Battery Cell relative to its nominal capacity also has an effect on the heat generated by the battery …

Heat pipe air-cooled thermal management system for lithium …

Fig. 1 shows a picture of the sandwiched heat pipes cooling system (SHCS) for a prismatic LTO battery cell with their dimensions. In this design, the cell is sandwiched by six flat heat pipes. The detailed parameters of the battery cell and heat pipes are presented in Table. 1.The SHCS quickly absorb and transfer the heat to the …

Two-phase immersion liquid cooling system for 4680 Li-ion battery ...

In general, the cooling systems for batteries can be classified into active and passive ways, which include forced air cooling (FAC) [6, 7], heat-pipe cooling [8], phase change material (PCM) cooling [[9], [10], [11]], liquid cooling [12, 13], and hybrid technologies [14, 15]. Liquid cooling-based battery thermal management systems (BTMs) have ...

Switchable Heat Pipes for Eco-Friendly Battery Cooling in …

To increase the temperature exchange with the environment, heat pipes are a great option. Heat pipes are available in various designs and are used, among other things, for efﬁcient heat transport and for homogenizing temperature ﬁelds [12]. Therefore, several studies regarding the use of heat pipes in BTMSs have been performed [9,10]. …

Battery thermal management systems based on nanofluids for …

Researchers have also examined heat pipes utilization in conjunction with other forms of cooling. An experiment by Ye et al. [197] used heat pipes and cooling plates to control the battery temperature. The use of heat pipes and phase change material in thermal management system (TMS) was studied by Yamada et al. [198] and Hata et …

Heat Pipe Learning Center

An Overview of Heat Pipe Technology. A heat pipe is a two-phase heat transfer device with a very high effective thermal conductivity. It is a vacuum-tight device consisting of an envelope, a working fluid, and a wick structure. As shown in the video below, the heat input vaporizes the liquid working fluid inside the wick in the evaporator section.

Thermal management technology of power lithium-ion …

However, the liquid-gas phase transition principle can also be used for effective thermal management of the battery, which typically includes heat pipe cooling and boiling cooling. Most heat pipes are made of metal and have good heat transfer properties [155], [156], [157]. The commonly used heat pipe consists of three parts: the …

A review of thermal management methods for electric vehicle …

Numerous researchers have performed research on diverse varieties of heat pipes, including flat heat pipes, micro-heat pipes, and oscillating heat pipes, and …

A review of heat pipe technology for foldable electronic devices

Rigid heat pipes are a well-established and widely applied technology for use with mobile devices. However, in the case of foldable electronics, if the heat-generating components are concentrated in one section of the device, more than 50% of the cooling area is removed as heat cannot be effectively transported through an articulating joint.

Thermal analysis of lithium-ion battery of electric vehicle using ...

The use of heat pipes in battery cooling not only enhances the overall performance and reliability of batteries but also contributes to extending ... After the addition of these features the total number of nodes obtained was 1,369,559 and the number of elements obtained was 5,309,287. ... is a type of rechargeable battery technology that …

A comprehensive review of heat pipe: Its types, incorporation ...

The entire content of the study is ordered as follows: Section 1 gives a brief introduction followed by a detailed discussion on different heat pipes in Section 2. Section 3 provides the significance of heat pipes from a design (sizing) point of view. Section 4 provides a brief discussion on the selection of working fluids. The various heat pipe …

Overview of heat pipe and applications in renewable energy …

Experimental Investigation On The Feasibility Of Heat Pipe Cooling For Hev/Ev Lithium-Ion Battery," ... Cold Energy Storage Systems Using Heat Pipe Technology For Cooling Data Centers," ... This Feature Is Available To Subscribers Only.

A review of battery thermal management systems using liquid cooling …

To address battery temperature control challenges, various BTMS have been proposed. Thermal management technologies for lithium-ion batteries primarily encompass air cooling, liquid cooling, heat pipe cooling, and PCM cooling. Air cooling, the earliest developed and simplest thermal management method, remains the most …

Li-Ion Battery Immersed Heat Pipe Cooling Technology …

In this study, a novel battery thermal management system (BTMS) based on FS49 is proposed and tested for cooling the cylindrical lithium-ion battery (LIB) module under fast charging...

Structure optimization of a heat pipe-cooling battery thermal ...

Usually, a battery pack with BTMS consists of cells, conduction elements, and cooling mediums. In the proposed battery pack, 18650 cylindrical cells are employed as power supply, L- shaped heat pipes and wave-shaped aluminum sheets are used as heat conduction elements, and a cold plate with parallel channels is used for cooling.

Heat-Pipe-Assisted Air Cooling of Lithium-Titanate Prismatic Battery

The present study about heat-pipe-assisted air cooling showed that out of six different configurations, four heat pipes with wick porosity 0.7, attached at the middle of two large surfaces of the lithium-titanate oxide (LTO) battery can reduce the maximum temperature below 40 °C and differential temperature below 5 °C of a single prismatic ...

Thermal management characteristics of a novel cylindrical lithium …

To improve the thermal performance of large cylindrical lithium-ion batteries at high discharge rates while considering economy, a novel battery thermal management system (BTMS) combining a cooling plate, U-shaped heat pipes, and phase-change material (PCM) is proposed for 21700-type batteries.

Heat pipes in battery thermal management systems for electric …

This review collates evidence that heat pipes can meet industry demand if used in EV BTMS; particularly aiming at fast charging applications, coupling heat pipes …